Extracts from Philips DTX3670 manual - method of selecting A/B code set and TV/VCR brands on the Philips DTX remote
To change your remote control from system A to system B.
1. Locate the 
(standby) and TEXT buttons on your remote control.
2. Simultaneously press and hold these two buttons for at least 3 seconds.
3. After releasing the
(standby) and TEXT buttons use the number buttons on the remote
to enter the three digit code 161.
Your remote is now programmed to work with system B commands.
Note: Should you at any time wish to change your remote control back, to work with system A commands, exactly the same sequence should be used except this time the code entered should be 160.
Important:
If your remote is not powered for more than one minute, for instance when the batteries are changed, it is possible your remote could revert back to system A and no longer works your digital receiver. Should this happen, please carry out the steps shown above to change the remote back to system B .
PROGRAMMING THE REMOTE FOR YOUR TV AND VIDEO
Your remote can control different major-brand televisions and video’s. Initially your remote is programmed for Philips-brand televisions and video’s. If you have different brands, follow the instructions below to set up your remote.
TV brand Setup
This applies to the TV only.
1. Turn on the television you wish to control.
2. Locate the
and P+ buttons in the TV
section of the remote control
(as shown below).
3. Simultaneously press both of these buttons for at least 4 seconds.
4. Enter the 3 digit code for the TV (found on pages 32 and 33).
5. Aim the remote at the TV and press the OFF button located in the TV section. The
television should now go to standby.
6. If the TV does not go to standby, repeat steps 2-5, trying each code listed for your
brand of TV.
VIDEO brand Setup
This applies to the video only.
1. Turn on the video for which the code needs to be identified.
2. Press and hold the 
and 
buttons simultaneously on the RC for a
minimum of 4 seconds.
3. Enter the 3 digit code for the video (found on pages 33 and 34).
4. Aim the remote at the video and press the yellow 
button (keep the side button pressed when the yellow 
button is pressed). The video should start
playback.
5. If the video does not start playback, repeat steps 2-4, trying each code listed for
your brand of video.
Resetting your remote
If necessary the remote can be reset to the factory default clearing all
the pre-programmed codes.
TV OFF and are pressed simultaneously
for at least 4 seconds. This restores the remote to the factory setting.
Changing batteries
When changing batteries in your remote, programmed codes will only be remembered for one minute. Be careful not to press any button when changing the batteries as this will also reset your remote.
See bottom of this page for code listing
Selectinng the A/B code set on the Philips DTX receiver
If you have interference between your digital receiver’s remote control and your particular brand
Your digital receiver and remote can work with one of two infra-red coding systems A & B. The
normal setting for your receiver and remote control is system A, these can however be changed
to system B, to avoid conflict with your television set.
10.1 To change your digital receiver from system
A to system B.
1.
Ensure your digital receiver is switched off (if necessary press the ON/OFF button)2.
Press the ON/OFF button to switch on your digital receiver (the front display shows the timeor “—:—”), your digital receiver will now be in standby.
3.
Press and hold the M button on the front panel of your digital receiver for at least 3 seconds.4.
The front control panel of the digital receiver will now show “-SA-” (this stands for system A).5.
Press the B (right arrow) button to change the display from “-SA-” to “-Sb-”.6.
Press the S button to store the displayed setting, your digital receiver returns to standby andis now programmed to use system B.
Note:During the above process, if there is a time lapse of more than 10 seconds between
key presses the digital receiver will return to standby.
Should you at any time wish to change your digital receiver back to system A commands, exactly
the same sequence should be used except this time the
B (right arrow) button is used to changethe display to “-SA-”.
10.2 To change your remote control from system
A to system B.
1.
Locate the B (standby) and TEXT buttons on your remote control.2.
Simultaneously press and hold these two buttons for at least 3 seconds.3.
After releasing the B(standby) and TEXT buttons use the number buttons on the remoteto enter the three digit code 161.
Your remote is now programmed to work with system B commands.
Note: Should you at any time wish to change your remote control back, to work with system
A commands, exactly the same sequence should be used except this time the code
entered should be 160.
Important:
If your remote is not powered for more than one minute, for instance when the batteries are
changed, it is possible your remote could revert back to system A and no longer works your
digital receiver.
Should this happen, please carry out the steps shown above to change the remote back to
system B .
TV or Video settings you may have entered to operate products other than Philips will also be
lost. Refer to chapter 11 “Programming the remote for your TV and Video” for information about
these settings.
ASA 064, 108
Aiwa 027, 375, 379
Akai 068, 080, 133, 342
Akiba 099
Alba 047, 099, 236, 305, 342, 379
Ambassador 047
Amstrad 027, 305, 359
Anitech 099
Asuka 064
Baird 027, 068, 131
Basic Line 047, 099, 305
Blaupunkt 030, 033, 061, 181, 189,222, 253, 254, 430
Brandt 214, 347, 348
Brandt Electronic 068
Bush 099, 236, 305, 379
CGE 027
Catron 047
Cimline 099
Clatronic 047
Combitech 379
Condor 047
Crown 047, 099, 305
Cyrus 108
Daewoo 047, 305
Dansai 099
De Graaf 069, 193
Decca 027, 108
Denon 069
Dual 068
Dumont 027, 108, 131
ESC 267, 305
Elbe 065
Elcatech 099
Ferguson 068, 347, 348
Fidelity 027
Finlandia 108, 131
Finlux 027, 069, 108, 131
Firstline 064, 070, 072, 099, 236
Fisher 073, 074, 131
frontech 047
Funai 027
GEC 108
General 047
GoldHand 099
GoldStar 064, 252
Goodmans 027, 047, 064, 099, 305, 430
Graetz 068, 131, 267
Granada 073, 108, 131
Grandin 027, 064, 099
Grunding 030, 033, 034 ; 099, 108,222, 234, 253, 374, 376, 430
HCM 099
Hanseatic 064
Hinari 031, 099, 267, 379
Hitachi 027, 031, 068, 069, 193, 267
Hypson 099
ITT 068, 073, 131, 133, 267, 411
ITV 064, 305
Imperial 027
Ingersol 031
Interfunk 108
JVC 035, 068, 094, 233, 234, 411
Kaisui 099
kendo 133, 236
Kenwood 068
Korpel 099
Lenco 305
Leyco 099
Loewe 031, 033, 064, 108, 189
Logik 031, 267
Luxor 070, 073, 075, 131, 133
M Electronic 027
Manesth 072, 099
Marantz 030, 033, 108
Matsui 031, 063, 236, 375, 379
Melectronic 065
Marantz 030, 033, 108
Matsui 031, 063, 236, 375, 379
Melectronic 065
Memorex 027, 064, 073, 131
Memphis 099
Metz 030, 033, 189, 222, 254, 374
Minerva 033, 222
Mitsubishi 070, 094, 108
Multitech 027, 099
Murphy 027
Nec 065, 068, 094
Neckermann 108
Nesco 099
Nokia 068, 073, 131, 133, 267
Nordmende 068, 324, 347, 348, 411
Oceanic 027, 068
Okano 342, 375
Orion 031, 063, 236, 375, 379
Osaki 027, 064, 099
Otto Versand 108
Palladium 033, 064, 068, 099
Panasonic 189, 253, 254
Pathe Cinema 063
Pathe Marconi 068
Pentax 069
Perdio 027
Philco 065
Philips 108, 411, 430
Phonola 108
Pionner 094, 108
Portland 047
Profex 349
Profitronic 267
Proline 027
Pye 108
Quartz 073
Quelle 108
RFT 430
Radiola 108
Rex 068, 411
Roadstar 064, 099, 267, 305
SBR 108
SEG 267, 349
SEI 031, 108
Saba 068, 233, 234, 324, 347,348, 411
Saisho 031, 063, 236
Salora 070, 073, 133
Samsung 267, 459
Sansui 068, 094
Sanyo 073, 131
Saville 379
Schaub Lorenz 027, 068, 131
Schneider 027, 099, 108
Seleco 068
Sentra 047
Sharp 075
Shintom 099, 131
Shorai 031
Siemens 030, 033, 064, 108, 131, 222
Silva 064
Singer 072
Sinudyne 031, 108
Solavox 047
Sonolor 073
Sontec 064
Sony 038, 059, 060, 061
Sunkai 375
Sunstar 027
Suntronic 027
Tashiko 027
Tatung 027, 068, 108
Tec 047
Technics 189, 253
Teleavia 068
Telefunken 068, 214, 347, 348, 411
Tenosal 099
Tensai 027, 349
Thomson 068, 347, 411
Thorn 063, 068, 131
Toshiba 068, 070, 072, 108, 411
Towada 349
Uher 267
Universum 027, 033, 064, 108, 133,222, 267
Yamishi 099
Yokan 099
Yoko 047, 267